2013年06月
2013年06月23日
Titanium frame and fork
I just got Ti rear frame and front fork. These are not for the S2L-X below, but for other Brompton I have. I have a certain direction for how to mod the other Brompton, but I have not made decision for some detailes yet. Of course I am not going to make something similar to the following one. チタン製のリアフレームとフロントフォークを入手した。これらは以下の写真のS2L-X用ではなく、もう一つのブロンプトン用だ。そちらのブロンプトンの方向性は決めているが、細かいところはまだ決めていない。もちろん、この写真のブロンプトンと似たものにはしないつもりだ。
s2l_x at 01:44|Permalink│Comments(0)
2013年06月14日
Rinproject 3way handle bag
I got a bag for my Brompton..., called "3 way handle bag" made by Rinproject.
ブロンプトン用にバッグを購入した、「3 way ハンドルバッグ」と呼ばれるリンプロジェクトの製品だ。
Bottom size is approx. 19 x 10cm. Lid width is around 30cm.
底辺のサイズは約19 x 10cm程度 蓋の幅はおよそ30cm
This bag fits with either S handle or riser bar like this. Does not fit to M handle.
このバッグはSタイプのハンドルかこのようなライザーバーであれば付けられる。Mタイプには付けられない。
Back side has 2 Velcro tabs to roll onto handel bar. It is very easy to attach/detach from the bar. I am happy with this because of appropreate size and nice design.
裏面にはベルクロテープが2カ所ついており、ハンドルバーに簡単に取り付け取り外しが出来るようになっている。ほどよいサイズでデザインも気に入っているので満足している。
s2l_x at 23:12|Permalink│Comments(0)
2013年06月07日
Milled Front Axle Hook.
I have made front axle hook for my Brompton from aluminum ingot.
アルミの塊からブロンプトン用のフロントアクセルフックを作った。
Aluminum block and milling machine
アルミの塊とフライス盤
Comparison with original hook. Original hook consists from over 5 different parts. Milled piece is uni-body. Rubber pad was applied to the inside of the piece.
元のフックとの比較、純正は5つ以上のパーツから構成されている。今回削りだしたものは一体成形だ。本体の内側にはゴム製のパッドを貼り付けている。
Original: 28g, the one I made: 12g
元のフック: 28g、今回作った物: 12g
Fits well, no issue when folding.
折りたたみ時も問題が無く、おさまりも良い
In fact, aluminum block cost was less than 10US$ which is cheap enough. However, it took so much time to finish due to its complex shape. 2 sides of the piece slightly twisted, so I had to mill it in the right angle. To be honest, I do not feel like making 2nd copy concerning an effort to finish. But, of course I am happy to complete this mod.
アルミブロックは1000円以下だったので十分安いが、フックの形状が複雑なので完成までに相当時間がかかった。フックの2辺が微妙にねじれているため、正しい角度で削る必要があった。実際は、完成までの手間を考えると、もう一個作ろうという気にはならないところだが、この改造を完成させられたことは満足している。
アルミの塊からブロンプトン用のフロントアクセルフックを作った。
Aluminum block and milling machine
アルミの塊とフライス盤
Comparison with original hook. Original hook consists from over 5 different parts. Milled piece is uni-body. Rubber pad was applied to the inside of the piece.
元のフックとの比較、純正は5つ以上のパーツから構成されている。今回削りだしたものは一体成形だ。本体の内側にはゴム製のパッドを貼り付けている。
Original: 28g, the one I made: 12g
元のフック: 28g、今回作った物: 12g
Fits well, no issue when folding.
折りたたみ時も問題が無く、おさまりも良い
In fact, aluminum block cost was less than 10US$ which is cheap enough. However, it took so much time to finish due to its complex shape. 2 sides of the piece slightly twisted, so I had to mill it in the right angle. To be honest, I do not feel like making 2nd copy concerning an effort to finish. But, of course I am happy to complete this mod.
アルミブロックは1000円以下だったので十分安いが、フックの形状が複雑なので完成までに相当時間がかかった。フックの2辺が微妙にねじれているため、正しい角度で削る必要があった。実際は、完成までの手間を考えると、もう一個作ろうという気にはならないところだが、この改造を完成させられたことは満足している。
s2l_x at 16:43|Permalink│Comments(0)
2013年06月01日
Loro Bashamichi
Today, I went to Loro Bashamichi, located in Yokohama bay area.
今日は横浜港エリアにあるローロ馬車道に行ってきた。
Storefront photos
店先の写真
Brompton with Harris tweed bag
ブロンプトンとハリスツイードのバッグ
Then I went to Yamashita Park, there were lots of people as it was nice day.
この後、山下公園に行ったところ、天気が良いこともあり、多くの人で混雑していた。
*Noticed that I tend to take photos of my bike with the same angle, so I will try different ones.
*自分のバイクの写真をいつも同じ角度から撮ってしまう傾向があることに気づいたので、もっと違う角度もトライしようと思う。
今日は横浜港エリアにあるローロ馬車道に行ってきた。
Storefront photos
店先の写真
Brompton with Harris tweed bag
ブロンプトンとハリスツイードのバッグ
Then I went to Yamashita Park, there were lots of people as it was nice day.
この後、山下公園に行ったところ、天気が良いこともあり、多くの人で混雑していた。
*Noticed that I tend to take photos of my bike with the same angle, so I will try different ones.
*自分のバイクの写真をいつも同じ角度から撮ってしまう傾向があることに気づいたので、もっと違う角度もトライしようと思う。
s2l_x at 23:48|Permalink│Comments(0)