mod
2013年09月15日
3 -> 2 speed mod
Just found an article (JPN only) about modifying M3L to 2 speed.
I do not think 2 speed mod is answer for everyone, but this can be one of solution for better efficiency.
M3Lを2速化している記事を見つけたので、紹介したい。
2速がすべての人にとっての正解というわけではないが、効率を上げるためにはこういう方法もあるよということで。
I do not think 2 speed mod is answer for everyone, but this can be one of solution for better efficiency.
M3Lを2速化している記事を見つけたので、紹介したい。
2速がすべての人にとっての正解というわけではないが、効率を上げるためにはこういう方法もあるよということで。
s2l_x at 22:44|Permalink│Comments(0)
2013年09月08日
For a long ride...
For an upcoming long ride, I have updated grip and pedal.
近々予定のロングライドに備え、グリップとペダルを交換した。
My Brompton equiped with Ergon carbon grip and crankbrothers egg beater
エルゴンのカーボングリップとクランクブラザーズのエッグビーターをつけたブロンプトン
近々予定のロングライドに備え、グリップとペダルを交換した。
My Brompton equiped with Ergon carbon grip and crankbrothers egg beater
エルゴンのカーボングリップとクランクブラザーズのエッグビーターをつけたブロンプトン
s2l_x at 16:10|Permalink│Comments(0)
2013年06月23日
Titanium frame and fork
I just got Ti rear frame and front fork. These are not for the S2L-X below, but for other Brompton I have. I have a certain direction for how to mod the other Brompton, but I have not made decision for some detailes yet. Of course I am not going to make something similar to the following one. チタン製のリアフレームとフロントフォークを入手した。これらは以下の写真のS2L-X用ではなく、もう一つのブロンプトン用だ。そちらのブロンプトンの方向性は決めているが、細かいところはまだ決めていない。もちろん、この写真のブロンプトンと似たものにはしないつもりだ。
s2l_x at 01:44|Permalink│Comments(0)
2013年06月07日
Milled Front Axle Hook.
I have made front axle hook for my Brompton from aluminum ingot.
アルミの塊からブロンプトン用のフロントアクセルフックを作った。
Aluminum block and milling machine
アルミの塊とフライス盤
Comparison with original hook. Original hook consists from over 5 different parts. Milled piece is uni-body. Rubber pad was applied to the inside of the piece.
元のフックとの比較、純正は5つ以上のパーツから構成されている。今回削りだしたものは一体成形だ。本体の内側にはゴム製のパッドを貼り付けている。
Original: 28g, the one I made: 12g
元のフック: 28g、今回作った物: 12g
Fits well, no issue when folding.
折りたたみ時も問題が無く、おさまりも良い
In fact, aluminum block cost was less than 10US$ which is cheap enough. However, it took so much time to finish due to its complex shape. 2 sides of the piece slightly twisted, so I had to mill it in the right angle. To be honest, I do not feel like making 2nd copy concerning an effort to finish. But, of course I am happy to complete this mod.
アルミブロックは1000円以下だったので十分安いが、フックの形状が複雑なので完成までに相当時間がかかった。フックの2辺が微妙にねじれているため、正しい角度で削る必要があった。実際は、完成までの手間を考えると、もう一個作ろうという気にはならないところだが、この改造を完成させられたことは満足している。
アルミの塊からブロンプトン用のフロントアクセルフックを作った。
Aluminum block and milling machine
アルミの塊とフライス盤
Comparison with original hook. Original hook consists from over 5 different parts. Milled piece is uni-body. Rubber pad was applied to the inside of the piece.
元のフックとの比較、純正は5つ以上のパーツから構成されている。今回削りだしたものは一体成形だ。本体の内側にはゴム製のパッドを貼り付けている。
Original: 28g, the one I made: 12g
元のフック: 28g、今回作った物: 12g
Fits well, no issue when folding.
折りたたみ時も問題が無く、おさまりも良い
In fact, aluminum block cost was less than 10US$ which is cheap enough. However, it took so much time to finish due to its complex shape. 2 sides of the piece slightly twisted, so I had to mill it in the right angle. To be honest, I do not feel like making 2nd copy concerning an effort to finish. But, of course I am happy to complete this mod.
アルミブロックは1000円以下だったので十分安いが、フックの形状が複雑なので完成までに相当時間がかかった。フックの2辺が微妙にねじれているため、正しい角度で削る必要があった。実際は、完成までの手間を考えると、もう一個作ろうという気にはならないところだが、この改造を完成させられたことは満足している。
s2l_x at 16:43|Permalink│Comments(0)
2013年06月01日
Another third party chain tensioner
It seems there will be another third party chain tensioner for Brompton might be available near future according to this information. Do not know when, but this sounds very interesting, as existing model is bit heavy.
どうやら他のメーカーからブロンプトン用のチェーンテンショナーが発売されるかもしれないという情報をこちらで見つけた。いつになるかわからないが、とても興味をもっている。というのも、今売っているものは少し重めだからだ。
どうやら他のメーカーからブロンプトン用のチェーンテンショナーが発売されるかもしれないという情報をこちらで見つけた。いつになるかわからないが、とても興味をもっている。というのも、今売っているものは少し重めだからだ。
s2l_x at 00:56|Permalink│Comments(0)